Materials Needed
- hunidicrib with RW holder if you have.
- Rock wool 1inch x 1inch
- Scalpel ans scissors
- Clonex or clone powder
- ATleast one Flouro
- A poker/ plastic spike to make holes in RW
- RIzotonic
- Water and bucket.
Rock wool cloning ->
Directions
1.
Get everything you need sterilise scissors, scalpel, humidicrib,poker in
water mixed with 1ml per liter of peroxide or bleach. While cleaning
prepare cube by soaking in PH 6.0 water and 4ml of Rizotonic per liter
for 4 hours
2.
Select mums or donor plant branches need atleast 5 nodes and should feel
woody mot too limp, Mum should be more than 8 weeks old very healthy and
well fed in week prior to cloning.
3.Rw
needs to have soak water removed 4 good flicks or shake, dont squeese as
cube becomes lesslikley to hold air and too much water.
4.
Holes should go 3/4 through cube so as it can support cut.
Clean and rinse crib, scissors and scalpel, Find a branch that is
suitable. Either remove whole 5/6 node branch and cut on chopping board
clean cut leaves off nodes leaving top two.
5.
Lay branch flat on board and select a node. 3 or 4 slices within 5mm
below node only scrathing stem and a 45 angle cutting right through
straight into cut solution for 10 seconds and then into cube. If leaves
are big remove 50% of larger leaves with scissors.
6.
With cut in RW it will wilt fast so needs to go straight into crib is
why i do 1 at a time, Cut will benifit from having her leaves trimmed
back slightly with a clean pair of sissors.
7.
once in the crib and all cuts are done close all vents add 500 ml of
rizo water into tray and foliar spray inside of crib and cuts. half hour
later if seal is good you will notice the humidity build if it does
there is no need to touch or open box for three days,
8.
3 days later i will update and water for first time only about 10/15ml
per cube
#3 days have
passed have not needed to water or open box was humid enough constant
moisture building , vents where opend half way top open full on 3rd day
temps got a little high about 28c but no sign of damage
They have all made
it so 100% can be expected now, if there going to die/ fall or disease
they would have done so or shown signs of stress by now. Have not fed at
all just rizo in the water for crib but will foliar feed dutch Master
foliatech in next few days to keep green. Cubes are quite dry but can go
another day, although humidity is dropping with vents open.
Ccubes can be
picked up to see how much water is in them if there light the need 15ml
water if med/heavy leave or drain out of cube some times when moisture
is high drops of water fall from roof of crib and overwater cubes, is
why it is important to check after 3 days
Day 6 or
7.. check for moisture in cubes use scales if your finding it
hard if i dought add 10ml if it runs out of cube dont water again until
rooted. All vents are fully opened today to harden up a bit and crid lid
was removed to breath for 5 min, becareful dont walk away as they can
wilt if done to early. Crib is pretty warm when checked i had to chech
if id turned heater on was just heat from light and water in base.
Pics from day
seven No roots yet
This pic prolly isnt needed but its now 7 whole days since removing from
plant, They where checked again today 3 days since watering and opening
vents half way. Moisture in cubes was still high so no need to water but
i did need to add more water to crib tray about 500ml plain water this
time. Think i will wait for first cubes to root to start foliar feeding
about half of the cuts have grown a few new nodes about 1cm growth this
is a sign all is good and roots are not far away with 3/4days but we
will see. If you wanted ive done before foliar feed from day 3 no chance
of yellowing from no food.
Cuts are all healthy i used cocktal spikes to support but they where
only there for the first 3 days and never really needed them but makes
for straight cuts.
Day 9
First cube rooted,
Cube should be planted into a cup of coco or into larger rock wool to
keep roots healthy.
One cut is showing slight yellowing maby got too much water or is rooted
and wants food, experimenting here so i fed it plain R/O water if its
hungry yellowing should get worse.
Soon as roots are visable foliar spray with weak nute and start rizo in
to feeds still around 15/20 ml per cube until in coco/bigger RW.
This cut will be kept for a mum if is stays healthy and grows well
12 DAY
All but three cubes are rooted well, the three behind seem to be wettest
and of Rhino strain. Looking back i think 500ml of water in base of crib
made for too much moisture what ive done in the past to raise humidity
was to add two large rock wool cubes wet in with rooting cuts from day
1. I should of have had a humidity metre in crib around 80%RH would be
ideal inside crib with all vents closed .
When lid was removed today within seconds leaves curled up slightly a
sign that some cuts still needed the protection and humidity, Today i
will remove lid twice for five minutes, three/ four times tomorrow and
if they look ok leave it off.
Rooted cuts have been planted into coco in insulated foam cups, clear
BEER cups are abit bigger and better suited if cuts are spending a week
or more in Preveg but need to be covered with plastic or paper to keep
light out preventing green mould through roots.
A couple of pics showing the repot and yellowing of Rhino cut, BB looks
very good. Hmmmmm
WR isnt getting worse as far as i can tell, This often happens to my
cuts soon as they hit the coco and nutes they repair themselves. ONly
one cause overwatering so i still have a way to go before i master RW
cloning.
I like to kEep it simple and compact so RW is the go for me and my
future cloning.
Ive done another batch of HP cuts from cuts of seed plant all are 100%
sexed now, i ended up with 3 good growing FEms worth flowering . Flower
room is just about full so i will veg HP for 2 months cutting back clone
again and try to fit into next grow for there grow off against BB.
Happy cloning peoples
|
Button
Ads!
Custom Search
